DFRobot DFR0282 Beetle Arduino-Compatible Microcontroller

DFRobot DFR0282 - The new generation" beetle" controller derives its core notion from minimalism without compromising functionality. It comes with atmel atmega32u4 @16mhz clock time and has expanded amounts of interfaces: 10 digital pins, 5 analog pins and 4 PWM pins. Micro usb: 1. 20mm x 22 mm compact size. Direct downloading and testing via micro usb.

Select" arduino leonardo tools > board > arduino leonardo in arduino ide, the atmega32u4 comes pre-burned with a bootloader that allows you to upload any new Code that is applicable to arduino leonardo. To further make it user-friendly, it is compatible with Micro USB so that direct programming and testing is no longer a headache.

More information about DFRobot DFR0282

Adafruit Trinket - Mini Microcontroller - 5V Logic ADA1501

Adafruit 100232 - You can't stack a big shield on it but for many small & simple projects the Trinket will be your go-to platform. Simply use a usb v2 port or a usb hub in between attiny85 on-board, 512 byte of sram, 8K of flash, 512 bytes of eeprom internal oscillator runs at 8MHz, but can be doubled in software for 16MHz.

Usb bootloader with a nice led indicator looks just like a USBtinyISP so you can program it with AVRdude with a simple config modification and/or the Arduino IDE with a few simple config modifications. Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lot of power.

One is 3v and one is 5V. Up to 16v input, reverse-polarity protection, thermal and current-limit protection. The 3v version should only run at 8 MHz. Use the 5v one for sensors and components that can use or require 5V logic. There are some things you trade off for such a small and low cost microcontroller! Trinket does not have a Serial port connection for debugging so the serial port monitor will not be able to send/receive data Some computers' USB v3 ports don't recognize the Trinket's bootloader.

Adafruit Trinket - Mini Microcontroller - 5V Logic ADA1501 - Perfect for when you don't want to give up your expensive dev-board and you aren't willing to take apart the project you worked so hard to design. In fact we even made some simple modifications to the Arduino IDE so that it works like a mini-Arduino board. Even though you can program trinket using the Arduino IDE, it's not a fully 100% Arduino-compatible.

More information about Adafruit 100232


Similar products:


ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 Nano x 3 Without Cable

ELEGOO EL-CB-005 - Micro-usb jack for power and/or usb uploading, you can put it in a box or tape it up and use any USB cable for when you want to reprogram. 5. 25k bytes available for use 2. 75k taken for the bootloader. Attiny85 on-board, 512 byte of sram, 8k of flash, 512 bytes of eeprom internal oscillator runs at 8MHz, but can be doubled in software for 16MHz.

Usb bootloader with a nice led indicator looks just like a USBtinyISP so you can program it with AVRdude with a simple config modification and/or the Arduino IDE with a few simple config modifications. The power source is automatically selected to the highest voltage source. On-board 5. 0v power regulator with 150ma output capability and ultra-low dropout.

ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 Nano x 3 Without Cable - It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper. Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, RX, GND on one top, so users have more breadboard space. You could download the driver of Elegoo Nano V3.

0 at: http://bit. Ly/2pmf4in technical specs microcontroller: atmega328 architecture: avr operating voltage: 5 v\ flash memory: 32 kb of which 2 kb used by bootloader sram: 2 kb clock speed: 16 mhz analog i/o pins: 8 eeprom: 1 kb dc current per i/o pins: 40 ma i/o pins input Voltage: 7-12 V Digital I/O Pins: 22 PWM Output: 6 Power Consumption: 19 mA PCB Size: 18 x 45 mm Weight: 7 g Package Include : 3 X Nano Board ATTENTION: We dont have USB cables in this kit and you will need to buy a mini USB cable to use this NANO board.

Use the driver from above link.

More information about ELEGOO EL-CB-005


Similar products:


Aideepen Beetle Virtual Keyboard BadUSB Atmega32U4-AU Module Micro Development Expansion Board for Arduino Leonardo UNO R3

Aideepen - It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper. Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, RX, GND on one top, so users have more breadboard space. Flash memory: 32 kb atmega32u4 of which 4KB used by bootloader.

Use the driver from above link. It is a smallest, complete, and breadboard friendly board. On-board 5. 0v power regulator with 150ma output capability and ultra-low dropout. Operating voltage: 5V DC. It's got a pin layout that works well with the Mini or the Basic Stamp TX, ATN, power and ground on the other. The nano can be powered via the mini-b usb connection, 7-12V unregulated external power supply pin 30, or 5V regulated external power supply pin 27.

Aideepen Beetle Virtual Keyboard BadUSB Atmega32U4-AU Module Micro Development Expansion Board for Arduino Leonardo UNO R3 - . The power source is automatically selected to the highest voltage source. Microcontroller: ATmega32u4. Sram: 2. 5 kb atmega32u4. Specifications: frequency: 16 mhz digital i/o pins: 10 pwm channels: 4 analog input channels: 5 uart: 1 i2c: 1 micro usb: 1 package included: 1 x Beetle USB ATMEGA32U4 Development Board Attiny85 on-board, 512 bytes of eeprom internal oscillator runs at 8MHz, 8K of flash, 512 byte of sram, but can be doubled in software for 16MHz.

More information about Aideepen


Similar products:


HiLetgo 3pcs Pro Micro Atmega32U4 5V 16MHz Bootloadered IDE Micro USB Pro Micro Development Board Microcontroller Compatible to Arduino Pro Micro Serial Connection with Pin Header

HiLetgo® - If you're supplying unregulated power to the board, be sure to connect to the "RAW" pin on not VCC. Micro-usb jack for power and/or usb uploading, you can put it in a box or tape it up and use any USB cable for when you want to reprogram. 5. 25k bytes available for use 2. 75k taken for the bootloader. The nano is using the chips atmega328p and cH340, not FT232 as official Arduino, so pls.

2. It's got a pin layout that works well with the Mini or the Basic Stamp TX, ATN, power and ground on the other. The nano can be powered via the mini-b usb connection, 7-12V unregulated external power supply pin 30, or 5V regulated external power supply pin 27. Operating voltage: 5V DC. It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper.

HiLetgo 3pcs Pro Micro Atmega32U4 5V 16MHz Bootloadered IDE Micro USB Pro Micro Development Board Microcontroller Compatible to Arduino Pro Micro Serial Connection with Pin Header - Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, RX, GND on one top, so users have more breadboard space. Atmega32u4 running at 5V/16MHz. Sram: 2. 5 kb atmega32u4. Running at 16mhz and 5v, this board will remind you a lot of your other favorite Arduino-compatible boards but this little guy can go just about anywhere.

More information about HiLetgo®


Similar products:


Adafruit NeoPixel Jewel - 7 x WS2812 5050 RGB LED with Integrated Drivers ADA2226 Original Version

Adafruit 2226 - An 8mhz or faster processor is required. Comes as a single round board with 7 individually addressable RGB LEDs assembled and tested. The power source is automatically selected to the highest voltage source. Microcontroller: ATmega32u4. The nano is using the chips atmega328p and cH340, not FT232 as official Arduino, so pls.

Supported by arduino IDE v1. 01. Sram: 2. 5 kb atmega32u4. Flash memory: 32 kb atmega32u4 of which 4KB used by bootloader. Our detailed neopixel Uberguide has everything you need to use NeoPixels in any shape and size. It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper.

Adafruit NeoPixel Jewel - 7 x WS2812 5050 RGB LED with Integrated Drivers ADA2226 Original Version - Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, GND on one top, RX, so users have more breadboard space. Eeprom: 1 kb ATmega32u4. Power the whole thing with 5VDC and you're ready to rock. The leds are 'chainable' by connecting the output of one Jewel into the input of another.

On-board micro-USB connector for programming. Use the driver from above link.

More information about Adafruit 2226


Similar products:


eBoot 5 Pack Boost Converter Module XL6009 DC to DC 3.0-30 V to 5-35 V Output Voltage Adjustable Step-up Circuit Board

eBoot EXPSFD005850 - On-board 5. 0v power regulator with 150ma output capability and ultra-low dropout. Input: dc 3 v to 30 v, optimum operating voltage range: 5v to 30V; Output: DC 5 V to 35 V voltage is continuously adjustable, maximum output current is 4 A. Operating voltage: 5V DC. With mounting holes There are two mounting holes on the diagonal side, the holes are 0

139 inches/ 3. 53 mm, it is a good efficiency non-isolated boost module. Use the driver from above link. It is a smallest, complete, and breadboard friendly board. Up to 16v input, reverse-polarity protection, thermal and current-limit protection. You could download the driver of Elegoo Nano V3. 0 at: http://bit.

eBoot 5 Pack Boost Converter Module XL6009 DC to DC 3.0-30 V to 5-35 V Output Voltage Adjustable Step-up Circuit Board - Ly/2jklJMO. Stock type: NeoPixels >> Boards. Package includes: 5 x dc-dc step-up module Tips: Please check if the product package is intact before opening. Attiny85 on-board, 512 bytes of eeprom internal oscillator runs at 8MHz, 512 byte of sram, 8K of flash, but can be doubled in software for 16MHz. Usb bootloader with a nice led indicator looks just like a USBtinyISP so you can program it with AVRdude with a simple config modification and/or the Arduino IDE with a few simple config modifications.

The higher the voltage, current, the lower the efficiency switching frequency: 400 KHZ Output ripple: 50 mV the higher the voltage, the greater the no-load current Conversion efficiency: < 94 % the greater the pressure difference, the ripple is larger Load regulation: plus or minus 0.

More information about eBoot EXPSFD005850


Similar products:


Gy-521 MPU-6050 MPU6050 Module 3 Axis Analog Gyro Sensors+ 3 Axis Accelerometer Module

BlastCase BCEA259 - Sram: 2. 5 kb atmega32u4. Adafruit part Number: 2226. On-board micro-USB connector for programming. Micro-usb jack for power and/or usb uploading, you can put it in a box or tape it up and use any USB cable for when you want to reprogram. 5. 25k bytes available for use 2. 75k taken for the bootloader. The nano is using the chips atmega328p and cH340, not FT232 as official Arduino, so pls.

Use the driver from above link. It is a smallest, complete, and breadboard friendly board. Name: mpu-6050 modules three-axis gyroscope + three-axis accelerometer use the chip: mpu-6050 power supply :3-5v internal low dropout regulator communication modes: standard IIC communications protocol Chip built-in 16bit AD converter, 16-bit data output Gyroscope range: ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Immersion Gold PCB machine welding process to ensure quality Pin pitch 2.

Gy-521 MPU-6050 MPU6050 Module 3 Axis Analog Gyro Sensors+ 3 Axis Accelerometer Module - 54mm attiny85 on-board, 512 byte of sram, 512 bytes of eeprom internal oscillator runs at 8MHz, 8K of flash, but can be doubled in software for 16MHz. Usb bootloader with a nice led indicator looks just like a USBtinyISP so you can program it with AVRdude with a simple config modification and/or the Arduino IDE with a few simple config modifications.

Power supply :3-5v internal low dropout regulator. In stock & Ready to Ship. It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper.

More information about BlastCase BCEA259


Similar products:


5v Regulator, DROK 5pcs Mini Voltage Reducer DC 4.5-24V 12V 24V Step Down to 5V Buck Converter Board 3A Volt Step-Down Transformer Power Supply Module

DROK 2001708006 - On-board 5. 0v power regulator with 150ma output capability and ultra-low dropout. Parameters: Input Voltage: DC 4. 5-24v output voltage: Integrated adjustable and fixed output Adjustable range is 08-17v, fixed output are 1. 8v, 2. 5v, 3. 3v, 9v, 5v, 12v that can be chosen on the back side output Current: 3A max please enhance cooling work when it is full load; When real tested input 12V and output is 1.

5a, no need to add special system. Output reverse connection protection: no Enable Function Control: yes, Low electric level will stop working when high electric level is working. Conversion Efficiency: 97. 5% highest 6. 5v to 5v, 07a switch frequency: 500khz output ripple: 20mv12v to 5v, 3a  20m width operating temperature: -40℃ ~ +85℃Industrial class The higher the operation temperature is, the smaller the output power is Output Over-voltage Protection: no Temperature rising range at full load: 40℃ Static Current: 0

5v Regulator, DROK 5pcs Mini Voltage Reducer DC 4.5-24V 12V 24V Step Down to 5V Buck Converter Board 3A Volt Step-Down Transformer Power Supply Module - 85ma voltage adjustment Rate: ±05% dynamic response speed: 5% 200us Output Short-circuit Protection: yes, please don't keep making it short-circuit. Operating voltage: 5V DC. High electric level is 2-5V, low electric level is 0V or so. Rx and tx Hardware Serial Connections.

More information about DROK 2001708006


Similar products:


for use with CircuitPython & Arduino IDE - Adafruit Trinket M0

Adafruit Industries 3500 - Communication modes: standard IIC communications protocol. On-board micro-USB connector for programming. The adafruit trinket m0 is a tiny microcontroller board, built around the Atmel ATSAMD21, a little chip with a lot of power. Input: dc 3 v to 30 v, optimum operating voltage range: 5v to 30V; Output: DC 5 V to 35 V voltage is continuously adjustable, maximum output current is 4 A.

It's adafruit's lowest-cost circuitPython programmable board! It is the same form factor as the original ATtiny85-based Trinket. Xl6009 dc-dc adjustable step-up power converter module, the step-up circuit board is a good efficiency non-isolated boost module. Up to 16v input, reverse-polarity protection, thermal and current-limit protection.

for use with CircuitPython & Arduino IDE - Adafruit Trinket M0 - You could download the driver of Elegoo Nano V3. 0 at: http://bit. Ly/2jklJMO. Atmega32u4 running at 5V/16MHz. If the fixed output voltage is not what you want, you can adjust it by potentiometer. High efficiency and super compact size, high frequency and low ripple, wide range of applications, stable working performance, this 12v to 5v converter will be a good component for fixing work.

Strong and high quality construction: imported potentiometer and 3A current chip, high current shielded inductors and MLCC solid capacitance with long service life. Integrated enable port defaults the working mode and it will be off when it is at low electric level off, which bring a great convenience for users.

More information about Adafruit Industries 3500


Similar products:


0.96 Inch Yellow and Blue I2C IIC Serial 128X64 OLED Display Module for Arduino

DIYmall - Rx and tx Hardware Serial Connections. In stock & Ready to Ship. 4 x 10-bit adc pins, 12 x Digital I/Os. Supported by arduino IDE v1. 01. Step-up boost converter module: they can fix on the emergency lamp or other electronic devices between the corresponding voltage range, boost charger, DIY an output adjustable mobile power, etc.

Dsn6009 is a good-performance 400khz 4a switch currency step-up boost module; This module XL6009E1 is coming with the 3rd generation high-frequency switch technology as the core chip, the performance is much higher than LM2577. Supported voltage: 3. 3v-5v dc. Output current is 3a max please enhance cooling work when it is full load; when real tested input 12V and output is 1.

0.96 Inch Yellow and Blue I2C IIC Serial 128X64 OLED Display Module for Arduino - 5a, 3. 3v, adjustable range is 08-17v, 5v, fixed output are 1. 8v, no need to add special system. Output integrated adjustable and fixed voltage, you can get fixed output voltage by soldering the pot on the board. It's got a pin layout that works well with the Mini or the Basic Stamp TX, ATN, power and ground on the other.

The nano can be powered via the mini-b usb connection, 7-12V unregulated external power supply pin 30, or 5V regulated external power supply pin 27. Atmega32u4 running at 5V/16MHz.

More information about DIYmall


Similar products: